Hawking Technology HWUG1 Bedienungsanleitung

- 7 - 2.1 Verify Device Installation To verify that the device has been properly installed in your computer and is enabled, go to Start Æ Settings Æ

- 8 - 3 NETWORK CONNECTION Once the driver has been installed, you will need to make adjustments to your network settings. In Windows 98SE/ME 1.

- 9 - 4. Highlight Microsoft, and then double click on the item you want to add. Click OK. After returning to the Network screen, you can ma

- 10 - 6. Click the Access Control tab. Make sure that “Share-level access control” is selected. If connecting to a Netware server, share lev

- 11 - 9. Double-click the Network Neighborhood icon on the windows desktop, and you should see the names of the other PCs on the network. In Windo

- 12 - 3. After selecting the component you need, click Add… to install.

- 13 - 4. Select the network protocol you wish to add and click OK. This will return you to the Local Area Connections Properties window. 5. To

- 14 - 4 Configuration Utility The Hawking Wireless Configuration Utility is a powerful application that helps you configure the HWUG1 and monitor t

- 15 - 4.2 Site Survey When you open the Configuration Utility, the system will scan all wireless channels to find all access points/stations with

- 16 - 4.3 Profile The “Profiles List” is for you to manage the networks you connect to frequently. You are able to Add/Delete/Edit/Activate a profi

Trademarks & Copyright Windows 95/98/ME and Windows NT/2000/XP/2003 Servers are registered trademarks of Microsoft Corp. All other brands and p

- 17 - 4.3.1 Configure the Profile (Add/Edit a Profile) System Configuration Parameter Description Profile Name Define a recognizable profile name

- 18 - Ad-Hoc – Select this mode if you want to connect to another wireless station in the Wireless LAN network without going through an Access Poin

- 19 - 4.3.2 Authentication vs. Security Under the profiles tab, you are able to specify the type of security/authentication mode used to connect

- 20 - manually enters the starting password in their access point or gateway, as well as in each wireless stations in the network. WPA takes over au

- 21 - range) or 5-digit ASCII characters (including “a-z” and “0-9”) as the encryption keys. For example: “0123456aef“ or “test1”. 128-bit – Input

- 22 - To enable the WPA function in Windows XP, the following software systems are required: 1. Right-click the Windows wireless networks icon locat

- 23 - 4. In the Wireless Networks tab, select your preferred wireless network you are connected to and click on “Properties”.

- 24 - 5. Under the Association tab, select the type of Network Authentication your wireless network uses and determine the type of data encrypti

- 25 - .

- 26 - Parameter Description Network Authentication Open –No authentication is needed among the wireless network. Shared – Only wireless stations u

CONTENTS 1 INTRODUCTION... 1 1.1 Features ...

- 27 - 4.4 Link Status From the “Link Status” option, you can view all the information of the network you are connecting to. You can use this tool

- 28 - shown in the bar, the more radio signal been received by the card. This indicator helps to find the proper position of the wireless device for

- 29 - 4.6 Statistics This option enables you to view the available statistic information with its Tx counts (Tx success, Tx error, RTS Success and

- 30 - Wireless Mode 802.11 B/G mix – If you have a mix of 802.11b and 802.11g wireless stations in your network, it is recommended to setting the c

- 31 - CCX 2.0 Support Cisco Compatible Extensions function: 1. LEAP turn on CCKM 2. Enable Radio Measurement: can channel measurement every 0~2

- 32 - 5 UNINSTALLATION In case you need to uninstall the Utility and driver, please refer to below steps. (As you uninstall the utility, the driver

- 33 - 6 Troubleshooting This chapter provides solutions to problems usually encountered during the installation and operation of the adapter. 1.

- 34 - An integrated wireless and wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale

- 35 - wideband noise and is rejected (ignored) by most narrowband receivers. 13. What is Spread Spectrum？ Spread Spectrum technology is a wideba

- 1 - 1 Introduction Thank you for purchasing the Hawking Technologies HWUG1 Wireless 802.11usb Adapter with removable antenna. The removable anten

- 2 - 1.2 Specifications • Standard: IEEE 802.11b/g • Interface: USB 2.0 Type A • Frequency Band: 2.4000 ~ 2.4835GHz (Industrial Scientific Medi

- 3 - 1.4 Wireless Network Options / Quick Tutorial The Peer-to-Peer Network (also known as Ad-Hoc Mode) This network installation lets you set a s

- 4 - 2 Installation Procedure Before you proceed with the installation, please notice following descriptions. Note1: Please do not install the HWUG

- 5 - D. Choose “Hawking Configuration Tool” and click Next. E. Select “Optimize for WiFi Mode” and click Next. F. The system will begin to ins

- 6 - G. When the following screen appears, click Finish to complete the software and driver installation.